Dryer Vent Duct Products
|
We offer everything you need to hook up your dryer vent whether you go straight thru the outside wall or thru the attic to the roof or sidewall. We have various connectors for the back of the dryer to adapt to your particular application. And most of all, everyone needs their own Lint Extractor Brush to clean the lint out of the lint trap that gets by the screen. If you don't have one, get yours today & remember to clean your dryer duct every year. It needs to be disconnected and thoroughly cleaned and serviced to prevent a fire. You will have energy savings and your dryers life will also be extended. This will keep your drying cycle short and not burn out your heating elements and switches. Scroll down to view our Close Clearance Periscoping Pipes, Supurr-Flex Dryer Venting Products, Premium Flexible Dryer Vent Pipe, along with various elbows, collars, clamps, vent hoods, bird guards and 20'& 40' Dryer Vent Brush Assembly.
CLOSE CLEARANCE DRYER VENT PERISCOPE PIPES
RIGID ALUMINUM DRYER VENTING PRODUCTS
SUPURR-FLEX FLEXIBLE DRYER VENT DUCT
PREMIUM FLEXIBLE DRYER VENT PIPE
|
When an over-the-drum lint filter is pulled out,
there are still areas where lint has accumulated. This
flexible brush reaches inside the lint trap to remove excess lint.
You will need one of these to use
between Professional dryer vent cleanings. Works
with all dryer types. ITEM #
89200
PRICE $16.95
Close clearance dryer vent periscope pipes are
the only way to reduce the space behind the dryer from 4 1/2" to 2
1/2". Use them to position the dryer closer to a wall.
(The photo on far left shows the 29" - 50" periscope
pipe. The upper right photo shows the 18" - 29"
periscope pipe.) Both can be installed with the outlet end
either facing the dryer of turned away from the dryer. (The
lower right photo shows the 0" - 18" periscope
pipe.) Use this one when the dryer exhaust and wall exhaust
are close but do not exactly line up. The excess can be easily
trimmed with snips as shown in the photo. In actual installation
you would also trim the excess off the top. 
Here's a line of 4"
rigid aluminum dryer vent pipe to use when replacing vinyl
ducts. Use 4" x 24" rigid dryer vent pipe when rigid pipe
is more suitable than flexible pipe. The eave vent hood
(right foreground) and through-the wall vent hood (middle) provide
great termination options. Use the close clearance elbow, on
right, back row, whenever possible. It will make a 90 deg.
turn in only 4 1/2"! Use the wall offset elbow, pictured on
left in the back row, the dryer offset elbow, middle of back row to
work with difficult outlets. Do not use more than one offset
elbow per installation. Use the extension collar (bottom left
in photo) when the wall pipe does not extend far enough. We
also carry 4" clamp to use when connecting dryer
vents. 
Our bird guard fits over
most existing exterior dryer or bath fan exhaust vents to keep
critters out. It measures 7 1/4" x 7 1/4". Reguires
four, no. 8 3/4" mounting screws (not included). ITEM #89225 PRICE
$8.95 
Old fashioned dryer
vents blow open and stay that way, allowing cold air to enter.
This dryer vent closure has a baffle which is protected from the
elements, eliminating this problem. It can be painted to match
the house. It shouldn't be used on any dryer vent run over 20'
long. ITEM
#89300 PRICE $28.95 
Supurr-Flex Flexible
Dryer Vent Duct is a sturdy, multi-layered flexible duct constructed
of three layers of aluminum and two layers of polyester. It
withstands temperatures up to 265 degrees F. Use it to replace
unsafe vinyl duct often found connecting gas or electric dryers to
the wall vent. Supurr-Flex Duct Connects easily to the back of
the dryer and the wall termination. 4" x 25' ITEM #89210 PRICE
$31.95 
This premium dryer vent pipe will give you ultimate
safety. It comes complete with snap-lock fittings so no
clamping is necessary when using our elbows or vent hoods ( featured
above). We sell this flexible dryer vent pipe in two lengths:
4" x 6' and 4" x 12'. Both are shipped compressed for easy
storage and handling. Choose the length you need and simply
stretch to fit. This pipe needs at least 4 1/2" clearance to
fit between the wall and the dryer. For tighter spaces, use
our close clearance periscope pipes featured
above. 
This Dryer Vent Brush Assembly is an excellent
inexpensive way to get in the dryer vent for your self if you have a
short run. Available in 20' and 40'
lengths.
