Dura-Vent DirectVent Pro
DirectVent appliances can easily be located next to a wall and vented through the wall without the expense of a chimney. Or vent them straight up the middle of the house. They're economical and homeowners like 'em! This precision fitting pipe safely vents flue gases, while providing incoming combustion air through the space between its inner and outer walls. DirectVent Pro has an inner wall of .020" aluminum and an outer wall of 26-ga. galvanized steel. The components twist lock together for quick, secure, fastener-free installation. We offer two sizes, 4" inner diameter with a 6 5/8" outer diameter and 5" inner diameter with an 8" outer diameter. Pipe lengths of 12", 24", 36" and 48" are available in cases of four or six in the galvanized finish. Individual pieces of pipe with a painted black finish are available in 6", 9", 12", 24", 36" and 48" lengths. Scroll on down for complete list of components. DirectVent Pro carries a Limited lifetime warranty. Most direct vent appliances are approved to be used with Dura-Vent DirectVent Pro. In fact, it's the most recommended system on today's market. *We will contact you after you order with the exact shipping cost to ship to your area. Click here for shipping disclaimer.
Scroll down to see our Class-A Chimney Conversion Kit, Masonry Chimney Kit, Co-Linear Chimney Liner System and Dura-Vent Aluminum Chimney Liner. Below are pictures and prices for our Rain Caps, Ceiling Supports, Flashing & Storm Collar, Wall Thimble, Starter Collar for VC Stoves and Termination Kits.
Class-A Chimney Conversion Kit
Kit includes a Cap Adaptor and a Retro Connector Collar, shown above in picture. You will need to purchase separately a 4" Aluminum Liner and a 4" X 6 5/8" DirectVent Rain Cap. Refer to stove manufacturers' installation instructions for information on testing and listing of each appliance. Note: Be sure to check each Kit for our listing of which brands of chimney can be converted using this system.
KIT A fits these brands of chimneys:
KIT B fits these brands of chimneys:
KIT C fits these brands of chimneys:
Masonry Chimney Conversion Kit
Kit includes a Cap Adaptor, 18" X 18" Top Plate, Retro Connector Collar, and Wall Thimble Cover (all shown above). A 4" X 6 5/8" Rain Cap and 4" Aluminum Liner are necessary for the installation, each sold separately. Refer to the stove manufacturers' installation instructions for information on use of this system with a specific appliance.
The High Wind Horizontal Cap is shown in the center in picture. The Snorkel Cap is featured at top right in above picture - it is used when a manufacturer specifies a minimum height. The two bottom caps, shown in picture, are for vertical installations. The Vertical High-Wind Cap on the left should be used for high wind conditions. The shorter Vertical Low-Profile Cap on right in above picture, is used for low-profile installations.
Flashing, Firestops, Shields And Storm Collar
Also order a Round Ceiling Support/Wall Thimble Cover unless you are using the Termination Kit.
Dura-Vent Aluminum Chimney Liner Note: Always check appliance manufacturer's specifications for liner sizing requirements.
Co-Linear Chimney Liner System
The Co-Axial to Co-Linear Appliance Connector, connects the 3" aluminum liners to the appliance. A Direct Vent Co-Linear Top Termination Kit, Below, terminates the liners at the top. Choose the appropriate 4" X 6 5/8" Direct Vent Rain Cap and 3" Aluminum Liner to complete your installation. INSTALLATION INSTRUCTIONS FRO DIRECT VENT GS CHIMNEY LINER SYSTEM FOR USE WITH GAS APPLIANCES
Refer to stove manufacturers' instructions for information on testing and listing of each appliance.
Co-Axial To Co-Linear Appliance Connector
We offer different Connectors for individual appliances. Check the price list for the Connector that is the right size for your Direct Vent appliance.
Co-Linear Kit with Flex
*We will contact you after you order with the exact shipping cost to ship to your area. Click here for shipping disclaimer. |
The Dura-Vent DirectVent Pro Factory-Built
Chimney Conversion Kit converts to an
existing factory-built chimney system to a direct venting
system. In the conversion, you'll install 
The Masonry Chimney Conversion Kit allows venting
of your Direct Vent stove through an existing masonry chimney when
allowed by the appliance manufacturer. 
The Square Horizontal Termination Cap, shown at the top left in
picture, is shown with the Horizontal Wind
Guard which may be required in high wind areas or used as a
safety heat shield to prevent people from coming in contact with the
Rain Cap.
The Cathedral Ceiling Support Box is 14" tall. The
Round Ceiling Support/Wall Thimble Cover is used for flat ceilings or as a 
Flashings available for adjustable roof pitches
9/12" to 12/12". Firestops and Shields also. Storm Collar, sold
separately, seals above the flashing. 
Use this Wall Thimble to go through a combustible
wall. A 10" X 10" framed opening is required.
This Starter Collar connects
most Vermont Castings Direct Vent stoves directly to Direct Vent
GS. Height is 15". 
This Horizontal Termination Kit includes a 90 degree
Non-adjustable Black Elbow, a Round Ceiling Support/Wall Thimble
Cover, a Square Horizontal Rain Cap, 24" Black Pipe and an 11"-14
5/8" piece of Adjustable Black Pipe Check manufacturer's
instructions to see if a 
Here's the Aluminum Chimney
Liner to use when converting existing
chimmeys to the Dura-Vent Direct Vent GS System. The 3" diameter is used with the 
This Direct Vent Chimney Liner
System uses two runs of flexible 3" aluminum chimney liner
within an existing masonry chimney. One vent exhausts gases,
the other provides incoming combustion air to the appliance.
This Co-Linear Top Termination Kit brings together
two, 3" liners so one 
This Co-Axial To Co-Linear Appliance Connector
adaptor connects a direct vent appliance to two, 3" aluminum
liners, which then attach to the 
Use when installing a direct vent co-linear into a masonry chimney. Kit includes: choice of
cap; and two aluminum flex lengths. High-wind Cap in 1st picture. Prairie Cap shown in 2nd picture.
This Snow Splitter is used to divert snow around chimney, vent, and roof flashing. It is constructed of paintable galvanized material. 
