HomeSaver RoundFlex 304/316-Alloy Relining Pipe
|
The 316-alloy has a lifetime warranty for wood, coal, oil, and non-condensing gas relining applications and is available in 3" - 16" diameters. The 316-alloy, popular in coal regions, contains molybdenum which protects against corrosion. HOMESAVER WARRANTIES PDF FILES RoundFlex diameters of 3" - 12" are UL/ULC Listed for wood, coal, oil, and non-condensing gas when installed according to the manufacturer's instructions. Special order lengths 3" - 16" are available - they are shipped from the HomeSaver's manufacturing plant. See prices below or contact us for more information. BE SURE TO READ PRODUCT AND ORDERING NOTES AT BOTTOM OF EACH PAGE.
Special Order Lengths are available in lengths of 10' to 50' in 3" - 10" diameters; 11" & 12" diameters are available up to 20'. SPECIAL ORDER FOR 13", 14", 15", and 16" RoundFlex: Scroll to bottom of page for more information and prices OR Click Here.
12-ga. Top/Bottom
Support Brackets (fits any size HomeSaver
Flex)
Universal Flex Connecting Band (fits any size HomeSaver Flex)
Product Note: CAUTION - this connecting band does not provide a male/female connection - use only when a regular Flex connector-adaptor is not available.
The detachable collar allows a 10" or 30" angle with the base. See our insert adaptor system for more options.
3" MALE to 4" FEMALE STAINLESS INCREASER
RoundFlex Tee With Removable Take Off See charts at bottom of page for Tee heights and Take-off lengths.
RoundFlex Tee with Long, Removable, Crimped Take Off The tee with 10" take-off (shown above right >) makes it easy to get down flues with off-sets. The 10" take-off is good for passing through thimbles. Note: 3" Tee has fixed take-off.
These plates are part of the UL/ULC system Listed in 3"-12" diameters for use with HomeSaver liners. The hole in these plates is sized just big enough to let HomeSaver RondFlex slip through during an installation and allow for thermal expansion. Naturally, these can be used either as a top plate - sealing the top of an installation, or as a bottom plate - giving bottom support for a fireplace reline. In the latter instance, these plates work perfectly when used in combination with our Bottom Plate Leg Support System, featured in Reliner Adaptors, Etc.
Top-Mounting Hardware Assembled On HomeSaver RoundFlex
This is how your typical HomeSaver RoundFlex installation looks on top. The top plate is generally sealed to the top of the crown or flue tile with silicone sealant. (Naturally, the piece of Flex showing below the top plate would be concealed within the chimney in a typical installation.) See installation instructions for complete details on your top termination. Regular Rain Cap and Guardian Cap
UL/ULC Listed HomeSaver Inverted Cone Cap
Special Order Lengths are available in lengths up to 20' for 13"-16" diameters. Product Note: FL indicates freightline shipment. Ordering Note: Cut-to-length pieces of HomeSaver liner are NON RETURNABLE, so please order carefully. Product Note: Outside dimensions of Flex pipe are determined by adding 1/4". Product Note: Flex pipe compresses during shipping and may need to be stretched out - instructions for stretching are included with all pipe. Product Note: All special order HomeSaver Flex pipe must ship via freight line (except 3" up to 25' lengths - these can ship UPS). Carriers require packaging on all liners. This cost will be calculated after we have shipping address. Product Note: HomeSaver RoundFlex liner can be used in conjunction with Heat-Fab pipe and fittings. If Heat-Fab is installed above the flex in an installation, no adaptor is needed. If the Flex is above Heat-Fab, use a connector-adaptor for the connection. HOMESAVER ROUNDFLEX TEE HEIGHTS AND TAKE-OFF LENGTHS 304 Tee, Flex With Fixed Take-Off
304 Tees, Flex With Removable Take-Off
304 Tee, Requires Use of Connector/Adaptor
304 Short Tee, Flex With Removable Crimped Take-Off, With Band Connection
316 Tee Flex With Removable Take-Off
316 Short Tee Flex With Removable Crimped Take-Off, With Band Connection
|
Nothing Beats RoundFlex for strength! Our
304-alloy RoundFlex has a lifetime warranty for wood burning and is
available in 3" to 16" diameters. 
Though convenient,
this Universal Flex Connecting Band does not provide a
"male-end-down" connection. Use only when a flex
connector-adaptor is not available (as with Dial-A-Flex).
Requires Make-A-Clamp Kit and pop rivets.
This cast iron insert boot covers the insert opening and
adapts to HomeSaver RoundFlex. Outside base is 10 1/8" wide x
15 3/8" long x 5 3/8" high, inner dimensions are 9 1/8" wide x 14
1/4" long. Attach by drilling and bolting, or tapping and
screwing into the insert tip. Then seal the boot's base to the
insert with Furnace Cement, Flue Goo, or Flat Fiberglass Stove
Gasket. Attach the liner to the boot with 1 1/4", No. 10
self-drilling stainless screws.
HomeSaver RoundFlex is very flexible, but it has a
substantial wall thickness and cannot be crimped.
You need this male/female connector-adaptor for the necessary
"male-end-down" joint. Use it when mating RoundFlex on top to
rigid pipe below, RoundFlex to RoundFlex, RoundFlex to
OvalFlex via a S-O Adaptor, or RoundFlex to RectangleFlex via a
S-R Adaptor. A connector-adaptor is not needed when mating
rigid pipe on top to flex pipe on bottom. 
The tee on the left
(>) features a special flared
top that allows HomeSaver RoundFlex to enter into it, giving you a
drip-free, "male-end-down" connection. Alternatively, you can
mate RoundFlex to a regular rigid tee by using the connector- adaptor,
featured above, as a transition between the tee and flex
pipe. Tee cover is sold separately.
There are two 316 stainless take-off options
here. The long one is uncrimped and 22" allowing for
connections thru thick chimney walls. The other is crimped and
5" allowing for a male end down on solid fuels. They are sold
separately - use them with a HomeSaver Tee. Available in 6"
and 8" diameter.
These 18-ga. 304-Alloy
HomeSaver RoundFlex Top/Bottom Plates with rounded corners feature a
nice, tall, raised lip around the hole. See price list for
specific sizes for top plates with 3"-10" diameter holes.
Plates with 11" and 12" holes are available in 18" x 18" only.
Special Order Plates are available, 
RoundFlex fits into
these rigid, flex/corrugated, nonadjustable 15, 30, 45, or 90 degree
elbows. They have flared ends so no connector-adaptor is
needed. 24-ga., 304-alloy stainless. 
Use a 20-ga. end-cone
to pull RoundFlex down past bends. Or attach to the Super
winch cable and pull up the flue. 
A storm collar minimizes moisture entry through the
hole in the top plate. You can't seal that hole - it needs to
be left open for thermal expansion of the liner. The 18-ga.
top clamp mounts under the storm collar and supports the liner by
providing a brace against the top plate. 
Though it's clear we prefer the 
This rain cap is a great choice for your
HomeSaver RoundFlex installations. Made of 100%, 304-alloy
stainless steel, this cap features an inverted cone underneath its
lid that directs creosote back down into the flue rather than onto
the roof and exterior masonry surfaces, its 3/4" mesh is
removable. Cap is available in 5" - 8" diameters.
