HomeSaver Pro 316 Ti-Alloy Stainless Relining Pipe
|
316 Ti-alloy is perfect for wood, coal, oil, and non-condensing gas - it resists corrosion and high-heat conditions. It is available in 3" - 12" diameters, including 5.5". Yep, at .006" thickness, it's even stronger than UltraPro; it's the industries strongest relining pipe. This strength advantage is the reason for a higher cost than UltraPro.
IT TAKES MINIMAL WRESTLING TO MAKE INSTALLATION - READY Though Pro is not as flexible as UltraPro it is way more user friendly than those light liners make on old technology machines. IT'S EVEN STRONGER THAN ULTRAPRO - AND WAY STRONGER THAN OTHER .006" LINERS While UltraPro has a crush resistance point of 288 lbs., Pro is way up at 337 lbs. Compare that to the other brand .006" liners we tested that were in the 140-160 lb. range. The strongest light liner is right here - HomeSaver Pro. IT'S PRICED FAIRLY FOR ALL ITS STRENGTH At only about 12% more cost than UltraPro, Pro is a bargain for the strength it delivers. SUPER WARRANTY - HOMESAVER WARRANTIES PDF FILES Naturally Pro is UL/ULC Listed when installed according to the instructions, and it comes with a lifetime warranty for wood, coal, oil and Category 1 gas appliances. The warranty is actually longer than lifetime because it is fully transferable to future owners of the home where Pro is installed. This improved warranty applies to all HomeSaver liners. INSTALLATION AND MAINTENANCE INSTRUCTIONS FRO HOMESAVER PRO CHOOSE FROM KITS, PRECUT LENGTHS, CUSTOM LENGTHS HomeSaver Pro is easy to buy. Choose our kits - see feature below, or our 25', 30', and 35' precut lengths, or if you want a custom length we can do that too. We can also ovalize Pro if you need it! CHOOSE POP RIVETS OR BAND CONNECTIONS WITH PRO Whereas with UltraPro we ask you to only use components with band connections, with Pro you can choose components that require rivets or screws - more flexibility of choice for you. Some chimney professionals even choose to use the beefy RoundFlex top mounting hardware with Pro, and that's totally fine. BE SURE TO READ PRODUCT AND ORDERING NOTES AT BOTTOM OF EACH PAGE. Relining Pipe 316-alloy
HomeSaver Pro Relining Kits
HomeSaver Pro & Ultra Pro End-Cones
Use a 20-ga. end-cone to pull HomeSaver down past bends. Or attach to the Super Winch cable and pull RoundFlex up the flue.
Cast-Iron Insert Boot and Adaptor   Adaptor
 Cast Iron Insert Boot
The adaptor provides a connection from Pro or UltraPro liner to a RoundFlex cast-iron insert boot. The adaptor attaches to the insert boot collar with screws.
Insert Kit - 304-alloy
Tees and Connector Adaptors with Band Connections 4" FEMALE to 3" FEMALE The
adaptor fits 3" Pellet stove collars when venting 4" UltraPro through masonry flues..
5.5" to 6" ADAPTOR Allows easy conversion from 5.5" UltraPro and Pro to 6'
PELLET VENT PRO ADAPTORS Joins UltraPro or Pro to PelletVent Pro using pop rivets.
See chart for tee heights and take-off lengths at bottom of page.  
 
Short
Flex Tee with Band Connection 
 The shorter body length of these tees offers greater user-friendliness in lots of installations. The second great feature of this tee is its long 10" take-off with band connection; the other tee's take-offs are only 5" and 22". Tee cover sold separately. There are many variances in tee lengths/take-off lengths of all tees. See price list for complete charts on tee specifications.
Removable Take-Off Options
22" female removable take-off is for use when going thru thicker walls and is sold seperately. Take-off ONLY
More Take-Off Options for Tees
Universal Take-Off 9 inch
Elbows with Band Connection
CollarPlate 304-alloy
Pyramid CollarPlate 304-alloy
This Collarplate with build-in clamp. Raised to add strength and shed water.
Terra Cotta CollarPlate 304-alloy
Use at end of tee snouts and off appliances. Crimp 1 1/4" in length, female 1 3/4" in depth. Must be used with one of hte connector adaptor options if used beneath Pro or UltraPro.
Mesh Bottom Plate 
Mesh parges on to smoke chamber ceiling for stable, sealed, smooth dome. This is factory direct item with custom cutting - allow extra delivery time.
These plates are part of the UL/ULC system Listed in 3"-12" diameters for use with HomeSaver liners. The hole in these plates is sized just big enough to let HomeSaver RondFlex slip through during an installation and allow for thermal expansion. Naturally, these can be used either as a top plate - sealing the top of an installation, or as a bottom plate - giving bottom support for a fireplace reline. In the latter instance, these plates work perfectly when used in combination with our Bottom Plate Leg Support System, featured in Reliner Adaptors, Etc.
Collar Plate Rain Cap & Guardian Cap
Insulation Kits
With both relining kits and insulation kits we've got your convenience needs covered. When should I insulate? Insulation is required for the liner warranty and UL 1777 listing for a solid fuel application. UL 1777 simulates severe usage in a residential setting including simulated chimney fires. A liner can only pass the heat transfer section of the test with proper insulation. Insulation prevents excessive heat transfer through the chimney structure to surrounding combustibles which otherwise could ignite. It also helps to reduce creosote deposits by keeping the flue gases hotter (contributing to a better draft).
Ordering Note: Cut-to-length pieces of HomeSaver liner are NON RETURNABLE, so please order carefully. Product Note: Outside dimensions of HomeSaver Pro/UltraPro Liners are determined by adding 3/8". Product Note: FL indicates freight line shipment. You will be contacted with any additional shipping costs before order is fully processed. Product Note: The 3" x 25', 4" x 25', 5" x 25', 5.5" x 25', and 6" x 25' relining kits ship UPS, all other kits must ship via freight line. Product Note: HomeSaver Pro/UltraPro Liners can be used in conjunction with Heat-Fab pipe and fittings. If Heat-Fab is installed above the HomeSaver Pro/UltraPro Liners in an installation, no adaptor is needed. If the HomeSaver Pro/UltraPro is above Heat-Fab, use a connector-adaptor for the connection. Product Note: The 5.5" tee comes with a 6" removable take-off. The bottom of the tee is also 6" so a 6" tee cover works perfectly on this item. HOMESAVER PRO TEE HEIGHTS AND TAKE-OFF LENGTHS HomeSaver Pro 316 Ti Tees Flex with Removable, Uncrimped Take-Off
HomeSaver Pro 316 Ti Tees With Removable Uncrimped Take-Off With Band Connections
HomeSaver Pro 316 Ti Short Tee With 10" Removable Uncrimped Take-Off With Band Connections
|
Read why HomeSaver Pro
is so popular! In Summary - UL/ULC Listed HomeSaver Pro is the
heaftier big brother of UltraPro. UL Listed to the 1777
Standard for zero clearance and ULC Listed to
S635-00. 
Patented mechanical roll lock seams are gas
tight. Custom cut lengths, ovalized to your specs, and shipped
the same day - precut lengths available
too.
Though you can get Pro in custom or precut lengths,
these ready-to-go kits are a super convenient option, too.
Each one contains an improved, welded-water-tight 13" x 13"
CollarPlate, and a CollarPlate Rain Cap - all with band connections
and 3/4" mesh, tee with removable take-off and band connection, tee
cover. Available in 25', 30', and 35' lengths. (See our
price list for what diameters are available.) 
Or, you can buy
just the components (without the liner) in kit form,
too. 
These end-cones in 6" - 12" are OUTSIDE MOUNT
for both our HomeSaver Pro and UltraPro liners. No
more need to drill holes and attach with screws. 
Offset Insert Adaptor, requires Offset Insert Adaptor Adaptor!
10 inch length and also
22 inch length
5 inch Take-off. 
4" Tee with 3" Take-off
• use this snout when venting gas directly
into HomeSaver liner by cutting
and sealing with RTV 
Elbows are sectioned and nonadjustable, with band connection. Available in 6" and 8" and in 15, 30, 45, or 90
degrees. No rivets or screws needed on band
connection end. 
Our CollarPlate supports the entire HomeSaver Pro or
UltraPro installation. It combines the top plate, storm collar
and top clamp into one convenient piece. its built-in clamp
just tightens with a screw driver. The CollarPlate now
features a welded, watertight seal. 
Our CollarPlate supports the entire HomeSaver Pro or
UltraPro installation. It combines the top plate, storm collar
and top clamp into one convenient piece. its built-in clamp
just tightens with a screw driver. 
Terra Cotta CollarPlate • same great collarplate with
built-in clamp but with a
formed bottom plate to anchor
into the sides of the tile. Available in 9 x 9, 9 x 13, 13 x 13 and 13 x 18 inch sizes. 
Reducers and
increasers allow you to connect pipe of different diameters.
The reducer (on left) has a crimp on the large end. The
increaser (on right) has a crimp on the small end. Remember,
for all solid fuel installations, the connections must be installed
with the male end down. 
These 18-ga. 304-Alloy
HomeSaver RoundFlex Top/Bottom Plates with rounded corners feature a
nice, tall, raised lip around the hole. See price list for
specific sizes for top plates with 3"-10" diameter holes.
Plates with 11" and 12" holes are available in 18" x 18" only.
Special Order Plates are available, 
Top Clamp (lower left) & Storm Collar (upper) 
The CollarPlate Rain Cap with 3/4" mesh is a
band connection version of our popular Guardian Cap. Just
attach it to the CollarPlate, turn a screw to tighten, and you're
done. See the finished installation shown in second
picture. 
These great kits give
you just the 1/2" HomeSaver Foil-Face FlexWrap you need for
either a 25', 30', or 35' reline job. Think of it, no
measuring and cutting. And these kits work for both Pro and
UltraPro installations. Each kit also contains ArmorMesh,
spray adhesive, foil tape, and a clamping kit. Remember,
insulation is needed for a UL/ULC Listing with HomeSaver, so be sure
to read our entire insulation features.
